Phase-technology Speaker Manuel d'utilisateur télécharger pdf (Page 2)

Be certain that you can get the speaker wire to the locations that you plan to mount the speaker

systems. Check with your Phase Technology dealer for their recommendation for the best wire for your

application but we suggest that you use a minimum of AWG #16/4 for the speakers. This will allow you

to have a pair of wires for both the left or right speaker and a separate 2 pairs of wires for the 2 center

channel speakers. Pre-run your speaker wire to the determined locations and be sure to leave about 2

feet of extra wire for the final speaker installation. Be certain to check for wall construction in the

desired mounting locations as mentioned above as well as the required hardware for the mounting

brackets. If the flat panel monitor is not yet mounted to the wall, mount the display first before mounting

the speakers.

Step 2

Using the mounting bracket as a guide measure equal distance from the top of the display and the

bottom of the display to the ends of the bracket. You need to allow a minimum of 1 ¼” from the edge of

the bracket side to the edge of the monitor so the speaker will clear the monitor when mounted to the

wall. Use a level to make sure you are mounting the bracket straight. With the bracket positioned in the

desired location use a pencil to mark the 4 mounting holes on the wall for the bracket mounting screws.

Drill the wall and install your anchors and screw the brackets to the wall.

Step 3

The pair of Arte’ speakers are sent as a matched mirror image pair of speakers. This means there is a

dedicated left speaker and a dedicated right speaker. There is a label on the rear of the speaker that

says “THIS END UP” that indicates the correct orientation of the speaker when it is mounted. There

are 2 terminal assemblies on the rear of the speaker cabinet. The upper one indicated by the label is for

the left/right channel input wires. The bottom terminal is for the center channel speaker wire connection.

Connect the speaker wires to the correct terminals observing the polarity indicated on the terminal.

Strip about ½” of insulation from the wires and separate the wires as necessary. If you are using other

wire lugs or connectors, attach them at this time to the bare wire. Unscrew the binding post terminals

and slip the stripped end of the wire through the hole in the metal post. Secure the wire in the post by

tightening the binding post terminal nut down on the bare wire or lug. Make sure the nut is tight and the

wire will not pull out of the terminal by lightly pulling back on the wire.

Step 4

The sturdy steel wall brackets supplied with the speakers are designed to attach to the key-way metal

slotted mounts on the rear of the speaker cabinet. Simply align the posts on the brackets with the holes

in the keyhole hangers and allow the speaker to slip down over the head of the bracket pins. Tuck the

speaker wire in behind the speaker cabinet and if necessary neaten up the wire with the use of tie

wraps.

Step 5

The Arte’ speakers are designed as a front LCR system that operates from a single pair of speaker

cabinets. As such the speaker hookup is treated the same as hooking up separate Left, Right and

Center speakers to a home theater receiver. The only difference is that you have 2 pairs of wires that

are connected to the amplifier’s center channel speaker output connection. The left and right pair of

wires are connected to their respective left and right speaker output terminals on the amplifier. Be

certain to observe the speaker polarity and refer to your amplifier manual for further information on

connecting your speakers.

Step 6

Since the Arte’ speakers form the front 3 speakers in a home theater system for flat panel displays they

are to be used and set up as you would normally for any 5.1 to 7.2 surround sound system for balance

and level adjustments. The amplifier should be set to the small speaker mode for best performance and

the subwoofer setting should be set to 100Hz. We recommend the use of our Phase Technology

subwoofers and surround speakers for complimenting your installation.

218-2072

The Arté is a unique 2-way systems for right and left main

+ center channel applications. Dual 5.25" RPF Kevlar-

laminated solid piston drivers and dual 1. user-adjustable

soft dome tweeters offer superb sound quality for all three

front channels from just two speakers. The proprietary

mounting systems are included for the on-wall with optional

stand mount and flat panel display systems mounting

available.

Tweeter Two 1" user-adjustable soft dome

Woofer

Two 5.25" RPF Kevlar-laminated

solid flat-piston drivers

Dimensions 9" (W) x 24" (H) x 3.5" (D)

Frequency 80 Hz - 22 kHz ( 3 dB)

Sensitivity 88 dB

Impedence 4 Ohms (Main); 8 Ohms (Center)

Finish Gloss Black or Gloss Silver

Weight Each 17 lbs

1 2

FLAT PANEL 1
MULTI-CHANNEL SPEAKER 1

Commentaires sur ces manuels

Pas de commentaire

Phase-technology Speaker Manuel d'utilisateur Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Microphones Phase-technology Speaker